Welcome to LUMITASK™. Exclusively featuring SEWLITE™ and LUMi™ products since 2013.



Product Instructions (Scroll Down to find your Model)

  

XTV Versa™ User Guide

Rechargeable Multipurpose Twin-Bright
Stereoscopic Flex Light

Thank you for purchasing the compact and
powerful cord-free SewLite xLITE Versa™ LED
Micro Task Light.  The ultimate All-in-One tool
for all your light needs.  Refer to guide before
using.

 
Unpacking the light

Identify and remove all contents from
packaging.

  • 5000 mAh Smart Power Bank with ON/OFF
    Switch with (2) removable NanoDOTZ™ 
    NanoTape Dots installed (keep liners)
  • (2) USB Flex Micro Task Lights
  • USB Micro Charging Cord
  • Detachable Magnet Plate

 
Required Tools

  • Isopropyl or cleaner (for cleaning mounting
    surfaces)
  • Warm water (for renewing NanoTape surface)
  • ATTENTION: Special NanoTape sticks to all
    surfaces.  When not in use, cover open tape with
    liner.

 
Mounting the light

Installing the micro task light requires 3-steps.
There are ZERO bulb changes, batteries to
replace, cords to loose, or tape to replace.
Simply re-mount over and over on any clean
smooth surface. Or wear on your clothing to
place light in front of you. Bend Flex Lights
for desired best lighting. 

  •  Make sure mounting surface is free of grease
    or dirt
  • Peel the NanoTape Liner and stick to machine
    surface.
  • Remove battery with gentle steady twist.
    Avoid prying.
  • Clean NanoTape surface with warm water if
    no longer holding well.
  • Double-stack NanoTape for best curved
    surface hold
  • Recharge battery up to 1000x. Clean tape up
    to 100x.

 
Operating the light

Turn ON-OFF with side button near bottom. Single
Click or plug-in Flex Light(s) for ON, double-click
for OFF. Use with one/two Flex Lights for 16hrs/8hrs
runtime. Temporarily attach to any smooth flat
surface using washable included NanoTape; or,
wear on your person using magnet clamping plate
by placing underneath your clothing. Adhere to all
medical device warnings for magnets. Optional
non-magnetic attach accessory is available. 

Battery level is shown as 4 LED dots in 25%
increments. Recharge with any micro-B or
micro-C charging cable. Charge rate is
determined by your USB charging source,
2hrs (typ).
 
Finally, when not using as a light, XTV can
charge up to three USB powered devices
using it's two USB-A and one USB-C ports
after unplugging both Flex Lights.

 

Maintaining the light

Your light is maintenance-free and water-dust
resistant by design.  It can withstand steam, food,
splashes, and even occasional drops! If it should
no longer stick, simply wash tape and let air-dry.
Use small tiny amount of soap if needed. 
DO NOT scrub tape.  NEVER clean with alcohol
or solvents.

 
Need Help?

If you need help troubleshooting or require
additional assistance with this product our
customer support staff is ready to assist you.

 
General Information       Genuine Parts

Online: Sewlite.com          Email: staff@neutek.us

Customer Service           8a – 2p, Mon- Thr, Arizona Time

staff@neutek.us               (excluding All US Holidays)

(844) LED-TASK

 
Special Notice

After pressing battery OFF button it is normal to
see a small “flicker” coming from lights. There is
no effect on the lights or battery life.

 
While charging the battery, the ON-OFF button
is defaulted to ON and will cause the Flex Lights
to remain ON if plugged in. To maximize battery
life, unplug charging cable at 100% charged.

 
Battery runtime can vary depending on its
configuration. Single Flex Light is up to 20hrs
while two Flex Lights is up to 10hrs.

 
This light is for general purpose hobby task
illumination only.


©2021 Sewlite. All rights reserved. Patents
pending. No part of this user guide may be
reproduced, distributed in any form without
permission of copyright owners.

 
Patented US D742,564 S

 

 

MachineLITELED

    M40           Light Where You Need It. TM

Congratulations on your purchase of your new MachineLITE™ LED task light for your machine.  Get ready for a whole new experience in sewing never before possible using our exclusive HD LED technology that installs in seconds.

Installation in Three Easy Steps – No tools required

  1. Wipe down surfaces with rubbing alcohol or mild cleaner.
  2. Plug into any standard Android USB cord; Touch ON-OFF.
  3. Experiment for best placement and light output needs, then peel and adhere light and round cord management TacDots™. Press firmly to activate tape bonding action.

NOTE: USB plug contains a power circuit and will run warm! See reverse side for Installation Tips and Troubleshooting.

Our HD LED Difference

Our goal is simple - to help you Love Life in HD! sm  In addition to ultra-long life, power savings, reduced heat and reliability, MachineLITE™ HD Illumination delivers clear High Definition “sunbrite white” light in areas never before possible. We’ve established strict standards for color temperature, color rendering, brightness and efficiency for the ultimate LED lighting experience.  Get ready to see clearly and comfortably – your eyes are going to love it.

 

User Installation Tips and Troubleshooting

MachineLITE not staying ON, Operating Erratically or False Triggering

For any new light re-location such as during initial setup or re-setup on a new machine, the Android USB cord should be temporarily un-plugged for 3 - 5 seconds to best properly re-establish correct Touch Sense surroundings for proper ON-OFF operation.

The Light is technically triggered by liquid (human finger) or metal.  Therefore placement on some machines may cause false triggering if metal is moving close-by underneath machine cover.  Try new different locations till operation is stable.

Light Does Not Turn ON or is Intermittent

Reliable Touch Light operation is very much also dependent on the quality and proper operating condition of the user provided USB Power Source which may include the following: Charging Cord, Plug Adapters, USB receptacles, USB Wall Adapters or Powerbanks, USB extension cords.

This simple operation Micro Task Touch Light was designed to conveniently run on most known working compatible commonly found USB power sources (0.5 amps rating or higher).  Depending on the model purchased, this could be a direct plug-in to a micro-USB Type B Charging / Power Cord; or, an Apple Lightning Cord through an Apple-to-Android Adapter; or, directly to a USB Type A Receptacle built into an appliance; or, as a portable USB Rechargeable Power Bank; or, a USB Type A Extension Cord. This includes all USB industry versions through present day as sufficiently providing minimum necessary power to run any USB powered Sewlite. Utilizing readily available USB sockets and cords keeps costs low and helps with recycling existing USB power cords. Examples are: USB powered or rechargeable appliances (e.g. Smart Phones, Smart Speakers, Watches, Tablets, Personal Wear Appliances, Flashlights, GPS, Rechargeable Batteries, Vaping, Wireless Speakers, Headsets, etc.) New USB cables, socket adapters, and Powerbanks may also be provided from the seller or purchased directly through Sewlite.

Sewlite Co. or the seller shall only be held responsible for warranty claims of Sewlite branded items themselves and not for indirect failure or improper operation caused from defective or non-compatible non-Sewlite branded new or used thrid party USB power sources (e.g. incorrect cord plug-ends, damaged or frayed cords, rechargeable batteries, worn sockets, wall adapters, non-powered USB ports, etc.). If experiencing any issues with a USB powered Sewlite, please first consider swapping out USB Power Source / Cord till proper operation is realized.  Otherwise, please consult retailer for separate warranty coverage on purchased compatible USB power source accessories.

100% Customer Satisfaction Guarantee

Our Sewlite products are guaranteed to the original owner against manufacturing defects in materials and workmanship, and normal wear and tear for the lifetime of the original owner. If a Sewlite product covered by this guarantee fails due to a manufacturing defect or normal wear and tear, we will replace the product, without charge, at our discretion. Only original unaltered and unmodified materials and workmanship are covered by this policy. This guarantee does not cover damage caused by improper use or environment. For guarantee evaluation, your product and original receipt must be returned directly to the Sewlite Warranty Dept PO Box 1061, Mesa, AZ  85211. Please include your email address and/or contact number. All shipping must be pre-paid and insured. Sewlite Co. cannot be liable for lost in-bound packages. This warranty is available worldwide.

Install Video Link: http://bit.do/MT80

©2022 SewLITE. All rights reserved. Other Patents pending. No part of this user guide may be reproduced or distributed in any form without permission of copyright owners.

 

 

MachineLITELED

    M80           Light Where You Need It. TM

Congratulations on your purchase of your new MachineLITE™ LED task light for your machine.  Get ready for a whole new experience in sewing never before possible using our exclusive HD LED technology that installs in seconds.

Installation in Three Easy Steps – No tools required

  1. Wipe down surfaces with rubbing alcohol or mild cleaner.
  2. Plug into any standard Android USB cord; Touch ON-OFF.
  3. Experiment for best placement and light output needs, then peel and adhere light and round cord management TacDots™. Press firmly to activate tape bonding action.

NOTE: USB plug contains a power circuit and will run warm! See reverse side for Installation Tips and Troubleshooting.

Our HD LED Difference

Our goal is simple - to help you Love Life in HD! sm  In

addition to ultra-long life, power savings, reduced heat and reliability, MachineLITE™ HD Illumination delivers clear High Definition “sunbrite white” light in areas never before possible. We’ve established strict standards for color temperature, color rendering, brightness and efficiency for the ultimate LED lighting experience.  Get ready to see clearly and comfortably – your eyes are going to love it.

 

User Installation Tips and Troubleshooting

MachineLITE not staying ON, Operating Erratically or False Triggering

For any new light re-location such as during initial setup or re-setup on a new machine, the Android USB cord should be temporarily un-plugged for 3 - 5 seconds to best properly re-establish correct Touch Sense surroundings for proper ON-OFF operation.

The Light is technically triggered by liquid (human finger) or metal.  Therefore placement on some machines may cause false triggering if metal is moving close-by underneath machine cover.  Try new different locations till operation is stable.

Light Does Not Turn ON or is Intermittent

Reliable Touch Light operation is very much also dependent on the quality and proper operating condition of the user provided USB Power Source which may include the following: Charging Cord, Plug Adapters, USB receptacles, USB Wall Adapters or Powerbanks, USB extension cords.

This simple operation Micro Task Touch Light was designed to conveniently run on most known working compatible commonly found USB power sources (0.5 amps rating or higher).  Depending on the model purchased, this could be a direct plug-in to a micro-USB Type B Charging / Power Cord; or, an Apple Lightning Cord through an Apple-to-Android Adapter; or, directly to a USB Type A Receptacle built into an appliance; or, as a portable USB Rechargeable Power Bank; or, a USB Type A Extension Cord. This includes all USB industry versions through present day as sufficiently providing minimum necessary power to run any USB powered Sewlite. Utilizing readily available USB sockets and cords keeps costs low and helps with recycling existing USB power cords. Examples are: USB powered or rechargeable appliances (e.g. Smart Phones, Smart Speakers, Watches, Tablets, Personal Wear Appliances, Flashlights, GPS, Rechargeable Batteries, Vaping, Wireless Speakers, Headsets, etc.) New USB cables, socket adapters, and Powerbanks may also be provided from the seller or purchased directly through Sewlite.

Sewlite Co. or the seller shall only be held responsible for warranty claims of Sewlite branded items themselves and not for indirect failure or improper operation caused from defective or non-compatible non-Sewlite branded new or used thrid party USB power sources (e.g. incorrect cord plug-ends, damaged or frayed cords, rechargeable batteries, worn sockets, wall adapters, non-powered USB ports, etc.). If experiencing any issues with a USB powered Sewlite, please first consider swapping out USB Power Source / Cord till proper operation is realized.  Otherwise, please consult retailer for separate warranty coverage on purchased compatible USB power source accessories.

100% Customer Satisfaction Guarantee

Our Sewlite products are guaranteed to the original owner against manufacturing defects in materials and workmanship, and normal wear and tear for the lifetime of the original owner. If a Sewlite product covered by this guarantee fails due to a manufacturing defect or normal wear and tear, we will replace the product, without charge, at our discretion. Only original unaltered and unmodified materials and workmanship are covered by this policy. This guarantee does not cover damage caused by improper use or environment. For guarantee evaluation, your product and original receipt must be returned directly to the Sewlite Warranty Dept PO Box 1061, Mesa, AZ  85211. Please include your email address and/or contact number. All shipping must be pre-paid and insured. Sewlite Co. cannot be liable for lost in-bound packages. This warranty is available worldwide.

Install Video Link: http://bit.do/MT80

©2022 SewLITE. All rights reserved. Other Patents pending. No part of this user guide may be reproduced or distributed in any form without permission of copyright owners.

 

 

MachineLITELED

    M120         Light Where You Need It. TM

Congratulations on your purchase of your new MachineLITE™ LED task light for your machine.  Get ready for a whole new experience in sewing never before possible using our exclusive HD LED technology that installs in seconds.

Installation in Three Easy Steps – No tools required

  1. Wipe down surfaces with rubbing alcohol or mild cleaner.
  2. Plug into any standard Android USB cord; Touch ON-OFF.
  3. Experiment for best placement and light output needs, then peel and adhere light and round cord management TacDots™. Press firmly to activate tape bonding action.

NOTE: USB plug contains a power circuit and will run warm! See reverse side for Installation Tips and Troubleshooting.

Our HD LED Difference

Our goal is simple - to help you Love Life in HD! sm In addition to ultra-long life, power savings, reduced heat and reliability, MachineLITE™ HD Illumination delivers clear High Definition “sunbrite white” light in areas never before possible. We’ve established strict standards for color temperature, color rendering, brightness and efficiency for the ultimate LED lighting experience.  Get ready to see clearly and comfortably – your eyes are going to love it.

 

User Installation Tips and Troubleshooting

MachineLITE not staying ON, Operating Erratically or False Triggering

For any new light re-location such as during initial setup or re-setup on a new machine, the Android USB cord should be temporarily un-plugged for 3 - 5 seconds to best properly re-establish correct Touch Sense surroundings for proper ON-OFF operation.

The Light is technically triggered by liquid (human finger) or metal.  Therefore placement on some machines may cause false triggering if metal is moving close-by underneath machine cover.  Try new different locations till operation is stable.

Light Does Not Turn ON or is Intermittent

Reliable Touch Light operation is very much also dependent on the quality and proper operating condition of the user provided USB Power Source which may include the following: Charging Cord, Plug Adapters, USB receptacles, USB Wall Adapters or Powerbanks, USB extension cords.

This simple operation Micro Task Touch Light was designed to conveniently run on most known working compatible commonly found USB power sources (0.5 amps rating or higher).  Depending on the model purchased, this could be a direct plug-in to a micro-USB Type B Charging / Power Cord; or, an Apple Lightning Cord through an Apple-to-Android Adapter; or, directly to a USB Type A Receptacle built into an appliance; or, as a portable USB Rechargeable Power Bank; or, a USB Type A Extension Cord. This includes all USB industry versions through present day as sufficiently providing minimum necessary power to run any USB powered Sewlite. Utilizing readily available USB sockets and cords keeps costs low and helps with recycling existing USB power cords. Examples are: USB powered or rechargeable appliances (e.g. Smart Phones, Smart Speakers, Watches, Tablets, Personal Wear Appliances, Flashlights, GPS, Rechargeable Batteries, Vaping, Wireless Speakers, Headsets, etc.) New USB cables, socket adapters, and Powerbanks may also be provided from the seller or purchased directly through Sewlite.

Sewlite Co. or the seller shall only be held responsible for warranty claims of Sewlite branded items themselves and not for indirect failure or improper operation caused from defective or non-compatible non-Sewlite branded new or used thrid party USB power sources (e.g. incorrect cord plug-ends, damaged or frayed cords, rechargeable batteries, worn sockets, wall adapters, non-powered USB ports, etc.). If experiencing any issues with a USB powered Sewlite, please first consider swapping out USB Power Source / Cord till proper operation is realized.  Otherwise, please consult retailer for separate warranty coverage on purchased compatible USB power source accessories.

100% Customer Satisfaction Guarantee

 Our Sewlite products are guaranteed to the original owner against manufacturing defects in materials and workmanship, and normal wear and tear for the lifetime of the original owner. If a Sewlite product covered by this guarantee fails due to a manufacturing defect or normal wear and tear, we will replace the product, without charge, at our discretion. Only original unaltered and unmodified materials and workmanship are covered by this policy. This guarantee does not cover damage caused by improper use or environment. For guarantee evaluation, your product and original receipt must be returned directly to the Sewlite Warranty Dept PO Box 1061, Mesa, AZ  85211. Please include your email address and/or contact number. All shipping must be pre-paid and insured. Sewlite Co. cannot be liable for lost in-bound packages. This warranty is available worldwide.

Install Video Link: http://bit.do/MT80

©2022 SewLITE. All rights reserved. Other Patents pending. No part of this user guide may be reproduced or distributed in any form without permission of copyright owners.

 

 

MachineLITELED

    M150      Light Where You Need It. TM

Congratulations on your purchase of your new MachineLITE™ LED task light for your machine.  Get ready for a whole new experience in sewing never before possible using our exclusive HD LED technology that installs in seconds.

Installation in Three Easy Steps – No tools required

  1. Wipe down surfaces with rubbing alcohol or mild cleaner.
  2. Plug into any standard Android USB cord; Touch ON-OFF.
  3. Experiment for best placement and light output needs, then peel and adhere light and round cord management TacDots™. Press firmly to activate tape bonding action.

NOTE: USB plug contains a power circuit and will run warm! See reverse side for Installation Tips and Troubleshooting.

Our HD LED Difference

Our goal is simple - to help you Love Life in HD! sm  In addition to ultra-long life, power savings, reduced heat and reliability, MachineLITE™ HD Illumination delivers clear High Definition “sunbrite white” light in areas never before possible. We’ve established strict standards for color temperature, color rendering, brightness and efficiency for the ultimate LED lighting experience.  Get ready to see clearly and comfortably – your eyes are going to love it.

 

User Installation Tips and Troubleshooting

MachineLITE not staying ON, Operating Erratically or False Triggering

For any new light re-location such as during initial setup or re-setup on a new machine, the Android USB cord should be temporarily un-plugged for 3 - 5 seconds to best properly re-establish correct Touch Sense surroundings for proper ON-OFF operation.

The Light is technically triggered by liquid (human finger) or metal.  Therefore placement on some machines may cause false triggering if metal is moving close-by underneath machine cover.  Try new different locations till operation is stable.

Light Does Not Turn ON or is Intermittent

Reliable Touch Light operation is very much also dependent on the quality and proper operating condition of the user provided USB Power Source which may include the following: Charging Cord, Plug Adapters, USB receptacles, USB Wall Adapters or Powerbanks, USB extension cords.

This simple operation Micro Task Touch Light was designed to conveniently run on most known working compatible commonly found USB power sources (0.5 amps rating or higher).  Depending on the model purchased, this could be a direct plug-in to a micro-USB Type B Charging / Power Cord; or, an Apple Lightning Cord through an Apple-to-Android Adapter; or, directly to a USB Type A Receptacle built into an appliance; or, as a portable USB Rechargeable Power Bank; or, a USB Type A Extension Cord. This includes all USB industry versions through present day as sufficiently providing minimum necessary power to run any USB powered Sewlite. Utilizing readily available USB sockets and cords keeps costs low and helps with recycling existing USB power cords. Examples are: USB powered or rechargeable appliances (e.g. Smart Phones, Smart Speakers, Watches, Tablets, Personal Wear Appliances, Flashlights, GPS, Rechargeable Batteries, Vaping, Wireless Speakers, Headsets, etc.) New USB cables, socket adapters, and Powerbanks may also be provided from the seller or purchased directly through Sewlite.

Sewlite Co. or the seller shall only be held responsible for warranty claims of Sewlite branded items themselves and not for indirect failure or improper operation caused from defective or non-compatible non-Sewlite branded new or used thrid party USB power sources (e.g. incorrect cord plug-ends, damaged or frayed cords, rechargeable batteries, worn sockets, wall adapters, non-powered USB ports, etc.). If experiencing any issues with a USB powered Sewlite, please first consider swapping out USB Power Source / Cord till proper operation is realized.  Otherwise, please consult retailer for separate warranty coverage on purchased compatible USB power source accessories.

100% Customer Satisfaction Guarantee

Our Sewlite products are guaranteed to the original owner against manufacturing defects in materials and workmanship, and normal wear and tear for the lifetime of the original owner. If a Sewlite product covered by this guarantee fails due to a manufacturing defect or normal wear and tear, we will replace the product, without charge, at our discretion. Only original unaltered and unmodified materials and workmanship are covered by this policy. This guarantee does not cover damage caused by improper use or environment. For guarantee evaluation, your product and original receipt must be returned directly to the Sewlite Warranty Dept PO Box 1061, Mesa, AZ  85211. Please include your email address and/or contact number. All shipping must be pre-paid and insured. Sewlite Co. cannot be liable for lost in-bound packages. This warranty is available worldwide.

Install Video Link: http://bit.do/MT80

©2022 SewLITE. All rights reserved. Other Patents pending. No part of this user guide may be reproduced or distributed in any form without permission of copyright owners.

 

 

xT200™ User Guide

Rechargeable Twin Quad-Bright Machine Light

Thank you for purchasing the compact and powerful cord-free
Sewlite xT 200™ LED Micro Task Light. The ultimate tiny flood
light for all your heavy duty machine lighting needs. Refer to
guide before using.

Unpacking the light

Identify and remove all contents from packaging.
5000 mAh Smart Power Bank with ON/OFF Switch
(2) Quad Bright Micro Task Lights
(4) 3M Command Strips
USB Micro Charging Cord
User Guide
Required Tools
Scissors (for trimming 3M Command tape)
Degreaser or Cleaner (for cleaning mounting surface)

Mounting the light

Installing the micro task light requires 3-steps. 1) Secure light and wires to any smooth clean machine surface using included tape and round TacDots. 2) Arrange battery similarly using command tape strip pairs on opposing surfaces. Space apart and crisscross for fast easy battery remounting. 3) Plug-in USBcord end of lights to either or both USB-A ports on the battery.

● Make sure all surfaces are free of grease or dirt
● Mount Command Tape spaced apart onto battery
● Mount Command Tape spaced apart onto machine
● Trim Command Tape as necessary for clean fit
● Choose a battery location next closest to lights
● Recharge battery up to 1000x using any USB-A port.

Limited Lifetime Warranty:    Under normal use, we will be happy to repair or replace your unit for life! The user is responsible for return shipping. We will not accept liability for more than product replacement. The user of this kit is responsible for safe and proper assembly and installation.

*Patented US  D754,196 

©2022 SewLITE. All rights reserved. Other Patents pending. No part of this user guide may be reproduced, distributed in any form without permission of copyright owners.

  

 

Flex™ User Guide     F4           F4S  

Reach Anywhere | Stick Anywhere Bendable Micro Task Light for Small USB-A PowerBanks

Thank you for purchasing the world’s smallest Full Spectrum LED Micro Task Light.  Turns your small cell phone PowerBank (Typ < 5000mAh) into portable “sunlight” task lighting.  101+ Uses. Never needs tape or Velcro.  Refer to this guide for use.

Unpacking the light

Identify and remove all contents from packaging.

  • 5” or 3” (shorty) bendable USB-A Flex Light
  • (2) NanoDOTZ™ NanoTape Dots (keep liners)

Required Tools & Accessories

  • Degreaser or Cleaner (for cleaning mounting surface)
  • Warm water with soap (for renewing tape surface)
  • ATTENTION: Special NanoTape sticks to all surfaces.  When storing, cover open tape with liner.
  • PowerBank User Guide

Mounting the light

Installing the micro task light requires 3-steps. There are ZERO bulb changes, batteries to replace, cords to loose, or tape to replace. Simply mount over and over on any smooth surface. Or plug USB light into any USB-A socket for additional applications.  Bend and adjust Flex Light up to 1000x  for desired best lighting.  

  • Make sure mounting surface is free of grease or dirt
  • Peel Single Tape Liner and attach to PowerBank first
  • Peel second Tape Liner and stick to machine surface.
  • Remove battery/light with gentle steady twist finger prying pressure. NEVER pry with a metal object.
  • Clean NanoTape surface if no longer holding well.
  • Tape cleaning or recharging can occur up to 1000x.

Operating the light

Turn ON-OFF by simply plugging into your PowerBank. Refer to your PowerBank guide for switched versions. Attach / de-attach PowerBank to any smooth flat surface using included  washable NanoDotz™. Maneuver the light exactly where needed using gradual bends and twists.  Never sharp 90 deg turns or bends.

Maintaining the light

Your light is maintenance-free, water-dust resistant and durable by design.  It can withstand drops, re-shaping, and even occasional scissors! If it should no longer stick, simply wash the NanoTape and let it air-dry.  Use a tiny amount of soap if needed.  DO NOT scrub tape.  NEVER clean with alcohol or solvents. NEVER bend / twist the light at sharp 90 deg angles.

Special Notice

When the light is OFF it is normal to notice a slight faint repeating flicker on the LEDs.  This will NOT drain the battery or harm the LEDs. It is by design for some smart PowerBanks to automatically “ON” whenever plugging into its USB-A port.

Battery runtime can vary depending on its usage and battery capacity in mAh. Expect 8 to 12 hours runtime per charge for most small PowerBanks.

This light is for general purpose hobby task illumination only.

Limited Lifetime Warranty:    Under normal use, we will be happy to replace or repair your unit for life! The user is responsible for return shipping. We will not accept liability for more than product replacement. The user of this kit is responsible for safe and proper assembly and installation.

Patented US D742,564 S

©2022 SewLITE. All rights reserved. Other Patents pending. No part of this user guide may be reproduced or distributed in any form without permission of copyright owners.